publication venue for
- Laser metal deposition as repair technology for Inconel 718 2025
- Joining of AA5052 to CF/PEEK by friction lap welding. 132:1137-1150. 2024
- Effect of cutting tool geometry on hole quality in orbital drilling. 131:827-841. 2023
- Combined effect of powder properties and process parameters on the density of 316L stainless steel obtained by laser powder bed fusion. 120:6187-6204. 2022
- Influence of abrasive water jet parameters on the surface integrity of Inconel 718. 114:997-1009. 2021
- Simulation of large-scale additive manufacturing process with a single-phase level set method: a process parameters study. 113:3343-3360. 2021
- A new method for choosing between ball-end cutter and toroidal cutter when machining free-form surfaces. 111:1425-1443. 2020
- Influence of a cutter’s main geometrical parameters on cutting forces in plunge milling of Ti6Al4V. 108:3835-3858. 2020
- Automatic minimal partitioning method guaranteeing machining efficiency of free-form surfaces using a toroidal tool. 107:4239-4254. 2020
- Experimental study of thrust force and surface quality when drilling hybrid stacks. 107:3981-3994. 2020
- Numerical and experimental study of the drilling of multi-stacks made of titanium alloy Ti-6Al-4V: interface and burr behavior. 107:1153-1162. 2020
- Modeling of air bubble dynamics during resin transfer molding by pore doublet model. 105:2343-2355. 2019
- Adaptive speed control for waterjet milling in pocket corners. 103:77-89. 2019
- Numerical modeling and experimental analysis of thrust cutting force and torque in drilling process of titanium alloy Ti6Al4V. 96:2815-2824. 2018
- A new cutting depth model with rapid calibration in abrasive water jet machining of titanium alloy. 93:1499-1512. 2017
- A new machining strategy for roughing deep pockets of magnesium-rare earth alloys. 92:3883-3901. 2017
- Stability of ball-end milling on warped surface: semi-analytical and experimental analysis. 89:2557-2569. 2016
- Balancing of the transversal cutting force for pocket milling cutters: application for roughing a magnesium-rare earth alloy. 89:45-64. 2016
- Machinability analysis of dry drilling of carbon/epoxy composites: cases of exit delamination and cylindricity error. 88:2557-2571. 2016
- Cutting forces and their modelling in plunge milling of magnesium-rare earth alloys. 84:1801-1820. 2015
- A new chain-processing-based computer vision system for automatic checking of machining set-up application for machine tools safety. 82:1547-1568. 2015
- Drilling of thick composite material with a small-diameter twist drill. 76:1543-1553. 2014
- Chatter in interrupted turning with geometrical defects: an industrial case study. 75:45-56. 2014
- Machining strategy in five-axis milling using balance of the transversal cutting force. 72:1377-1387. 2014
- Machining of complex-shaped parts with guidance curves. 69:1499-1509. 2013
- Influence of milling on surface integrity of Ti6Al4V—study of the metallurgical characteristics: microstructure and microhardness. 67:1477-1489. 2012
- Analysis of drift in iso-scallop planning—machining by regions. 67:719-732. 2012
- Torus cutter positioning in five-axis milling using balance of the transversal cutting force. 66:965-973. 2012
- Optimisation of workpiece setup for continuous five-axis milling: application to a five-axis BC type machining centre. 65:67-79. 2012
- Simulation of low rigidity part machining applied to thin-walled structures. 54:479-488. 2010
- Analytical models of composite material drilling. 52:609-617. 2010
- On the stability of high-speed milling with spindle speed variation. 48:883-895. 2009
- Kinematic modelling of a 3-axis NC machine tool in linear and circular interpolation. 47:639-655. 2009