selected publications

• academic article

  • Influence of wiper edge on surface integrity for end-milling of Ti-6Al-4V.  International Journal of Machining and Machinability of Materials.  25:89-89. 2023
  • Effect on surface integrity of high-productivity finishing on Ti-6Al-4V with wiper edge length tool.  Procedia CIRP.  108:406-411. 2022
  • Cutting parameters and tool geometry selection for plunge milling - Analysis of cutting forces at the bottom of deep titanium workpieces.  Journal of Manufacturing Processes.  62:491-500. 2021
  • Influence of a cutter’s main geometrical parameters on cutting forces in plunge milling of Ti6Al4V.  The International Journal of Advanced Manufacturing Technology.  108:3835-3858. 2020
  • Automatic minimal partitioning method guaranteeing machining efficiency of free-form surfaces using a toroidal tool.  The International Journal of Advanced Manufacturing Technology.  107:4239-4254. 2020
  • Adaptive speed control for waterjet milling in pocket corners.  The International Journal of Advanced Manufacturing Technology.  103:77-89. 2019
  • Effects of Selective Laser Melting additive manufacturing parameters of Inconel 718 on porosity, microstructure and mechanical properties.  Materials Science and Engineering A.  735:182-190. 2018
  • Analysis of the twist of ruled surfaces: application to strip machining.  International Journal of Manufacturing Research.  13:26-26. 2018
  • ANALYSIS OF THE TWIST OF RULED SURFACES. APPLICATION TO STRIP MACHINING.  International Journal of Manufacturing Research.  13:1-1. 2017
  • An analytical model taking feed rate effect into consideration for scallop height calculation in milling with torus-end cutter.  Journal of Intelligent Manufacturing.  30:1881-1893. 2017
  • A new cutting depth model with rapid calibration in abrasive water jet machining of titanium alloy.  The International Journal of Advanced Manufacturing Technology.  93:1499-1512. 2017
  • Balancing of the transversal cutting force for pocket milling cutters: application for roughing a magnesium-rare earth alloy.  The International Journal of Advanced Manufacturing Technology.  89:45-64. 2016
  • Studying the measurement by X-ray diffraction of residual stresses in Ti6Al4V titanium alloy.  Materials Science and Engineering A.  667:340-348. 2016
  • Modeling incision profile in AWJM of Titanium alloys Ti6Al4V.  Mechanics & Industry.  17:403-403. 2016
  • Milling plan optimization with an emergent problem solving approach.  Computers & Industrial Engineering.  87:506-517. 2015
  • Using the global optimisation methods to minimise the machining path length of the free-form surfaces in three-axis milling.  International Journal of Production Research.  53:5296-5309. 2015
  • Machining strategy in five-axis milling using balance of the transversal cutting force.  The International Journal of Advanced Manufacturing Technology.  72:1377-1387. 2014
  • Machining of complex-shaped parts with guidance curves.  The International Journal of Advanced Manufacturing Technology.  69:1499-1509. 2013
  • Study of the effective cutter radius for end milling of free-form surfaces using a torus milling cutter.  Computer-Aided Design.  45:951-962. 2013
  • Analysis of drift in iso-scallop planning—machining by regions.  The International Journal of Advanced Manufacturing Technology.  67:719-732. 2012
  • Torus cutter positioning in five-axis milling using balance of the transversal cutting force.  The International Journal of Advanced Manufacturing Technology.  66:965-973. 2012
  • Correlation between machining direction, cutter geometry and step-over distance in 3-axis milling: Application to milling by zones.  Computer-Aided Design.  44:1151-1160. 2012
  • Optimisation of workpiece setup for continuous five-axis milling: application to a five-axis BC type machining centre.  The International Journal of Advanced Manufacturing Technology.  65:67-79. 2012
  • Determination of angular fields outside low and high collisions to mill free-form surfaces on 5-axis CNC machines.  International Journal of Production Research.  50:1045-1061. 2011
  • Simulation of the behaviour of CNC machine-tools in three-axis milling of sculptured surfaces.  International Journal of Machining and Machinability of Materials.  8:326-326. 2010
  • Kinematic modelling of a 3-axis NC machine tool in linear and circular interpolation.  The International Journal of Advanced Manufacturing Technology.  47:639-655. 2009

• blog posting

  • Machining of complex-shaped parts with guidance curves.  arXiv (Cornell University). 2013

• chapter

  • Challenges in Additive Manufacturing: Influence of Process Parameters on Induced Physical Properties of Printed Parts.  . 1-31. 2024
  • Develop Model for Controlled Depth Milling by Abrasive Water Jet of Ti6Al4V at Jet Inclination Angle.  Lecture notes in mechanical engineering. 21-27. 2021
  • Influential Parameters in Plunge Milling for Titanium Alloy Ti-6Al-4V.  Lecture notes in mechanical engineering. 380-390. 2019
  • 5-Axis Flank Milling of Sculptured Surfaces.  Springer eBooks. 33-65. 2012
  • 5-axis Flank milling of sculptured surfaces.  HAL (Le Centre pour la Communication Scientifique Directe). 2012

• conference paper

  • A modeling of elementary passes taking into account the firing angle in abrasive water jet machining of titanium alloy.  AIP conference proceedings. 100005-100005. 2018
  • A new optimization tool path planning for 3-axis end milling of free-form surfaces based on efficient machining intervals.  AIP conference proceedings. 070011-070011. 2018
  • Machinability of Titanium Alloys (TA6V αβ, β) and workpiece deformation..  HAL (Le Centre pour la Communication Scientifique Directe). 2013
  • Using Clarke and Wright's Algorithm to Minimize the Machining Time of Free-Form Surfaces in 3-Axis Milling.  HAL (Le Centre pour la Communication Scientifique Directe). 2013
  • Analyse de la vrille des surfaces réglées, application à l'usinage par bande.  HAL (Le Centre pour la Communication Scientifique Directe). 2012
  • Positionnement d'outil torique avec équilibrage de l'effort de coupe transversal.  HAL (Le Centre pour la Communication Scientifique Directe). 2012
  • Detection and reduction of zones of burning in 5-axis machining of wooden parts.  HAL (Le Centre pour la Communication Scientifique Directe). 2009
  • Dynamic model of CNC milling machines.  HAL (Le Centre pour la Communication Scientifique Directe). 2009