selected publications

• academic article

  • A predictive model for the thermal contact resistance at liquid–solid interfaces: Analytical developments and validation.  International Journal of Thermal Sciences.  50:1445-1459. 2011
  • A predictive model for the evolution of the thermal conductance at the casting–die interfaces in high pressure die casting.  International Journal of Thermal Sciences.  49:365-372. 2009
  • Size effect in transient thermal fatigue testing and thermo-mechanical screening of coatings.  International Journal of Microstructure and Materials Properties.  3:311-311. 2008
  • The Accurate Determination of Heat Transfer Coefficient and its Evolution with Time During High Pressure Die Casting of Al‐9 %Si‐3 %Cu and Mg‐9 %Al‐1 %Zn Alloys.  Advanced Engineering Materials.  9:995-999. 2007
  • Estimation of concentration-dependent diffusion coefficient in drying process from the space-averaged concentration versus time with experimental data.  Chemical Engineering Science.  61:7185-7198. 2006
  • Estimation of local heat transfer coefficient on a cylinder: comparison between an analytical and an optimization method.  Inverse Problems in Science and Engineering.  13:449-467. 2005
  • Estimation of a heat source by using the measured temperatures and micrographic informations; application to an electron beam welding process.  Journal de Physique IV (Proceedings).  120:279-290. 2004
  • Estimations of a 2D convection heat transfer coefficient during a metallurgical 'Jominy end-quench' test: comparison between two methods and experimental validation.  Inverse Problems in Science and Engineering.  12:595-617. 2004
  • Determination of Reaction Parameters for Cardboard Thermal Degradation Using Experimental Data.  Process Safety and Environmental Protection.  81:1265-1270. 2003
  • Optimal Choice of Descent Steps in Gradient-Type Methods When Applied to Combined Parameter and Function or Multi-Function Estimation.  Inverse Problems in Science and Engineering.  11:273-288. 2003
  • THERMAL DOSE OPTIMIZATION IN HYPERTHERMIA TREATMENTS BY USING THE CONJUGATE GRADIENT METHOD.  Numerical Heat Transfer Part A Applications.  42:661-683. 2002

• conference paper

  • Influence des paramètres de rugosité pour la modélisation de la résistance thermique de contact à l\'interface tôle-outil en emboutissage à chaud.  HAL (Le Centre pour la Communication Scientifique Directe). 2010
  • A Model to Predict the Heat Transfer Coefficient at the Casting-Die Interface for the High Pressure Die Casting Process.  AIP conference proceedings. 2007
  • Détermination de modèles stoechio-cinétiques des réactions de dégradation thermique.  HAL (Le Centre pour la Communication Scientifique Directe). 2005
  • A normalized approach to optimize the coating/substrate couples with regards to thermal stresses : conditions for thermo-mechanical screening.  . 2005
  • Optimal Control of Thermal Damage to Targetted Regions in a Biological Material.  Volume !. 733-736. 2004
  • Estimation d'un terme source et de l'interface solide liquide dans un problème bidimensionnel : application au soudage par faisceau d'électrons.  . 2003
  • Validation expérimentale de l'estimation d'un coefficient 2D de transfert convectif par la résolution d'un problème inverse non linéaire.  HAL (Le Centre pour la Communication Scientifique Directe). 2002
  • Estimation of the Thermal Properties and Interface Conditions of Heterogeneous Materials.  . 201-209. 2002
  • Multi-Parameter Estimation in Hyperthermia Problem by Using an Optimal Choice of Descent Parameters in Iterative Methods.  . 29-35. 2002
  • Approche numérique de l'estimation d'un coefficient de transfert lors d'un essai metallurgique "essai jominy".  . 2001
  • Estimation of highly dynamic heat flux from surface temperature measurements using the adjoint method.  38th Aerospace Sciences Meeting and Exhibit. 2001